Products

  • 2018 New Gate Flash Lamp top 2018 New Gate Flash Lamp reviews
    Gate flash lamp with wide voltage range 12v-265v
    read more
  • Turbular Motor Receiver top Turbular Motor Receiver reviews
    1.Specification Power Supply: AC220V/50HZ. Loading Capacity: 2000W, AC240V. Frequency: 433.92 MHz. Memory Capacity: 50PCS rolling code remote control. External button and photocell protection. Working Temperature:  -20℃ to 60℃.
    read more
  • DC24V Sliding Control Board JJ-EG-32 JJ-EG-32
    一: Function: 1.       Board power supply:AC 24V, could connect 24V back up battery, 24V output for external device 2.       Use for DC sliding gate motor 3.       Transmitter: Giant rolling code transmitter, support max 120pcs transmitter 4.  24V DC motor 5.  Feature: digital display; limit; resistance sensitivity adjustable; motor speed adjustable; motor high speed time adjustable; motor protection time 60s; auto close function; auto close time adjustable; board single button control mode; resistance infrared; gate close infrared; PED mode; alarm lamp output; swipe card
    read more
  • IR Transmitter for Garage Door Automation IR Transmitter
    This EZY OPEN KIT works as an ideal hands free opening device for your gate automation systems. This kit includes 3 parts, the card reader installed near you gate automation system; the card put in behind the front window of vehicle;the external receiver wired to the gate automation system
    read more
  • Gate Flash lamp top Gate Flash lamp reviews
    I. Safety Instruction 1. For security, please read the user manual carefully before initial operation; 2. Please be sure the power is off before connecting, the product is produced without fuse; 3. This system must not endanger life or property during the running failure or its security risks have II. Technical Specification 1. working voltage: 12-265VAC /DC 2. Loading capacity: <3W 3. Flicker Frequency: 1HZ 4. Working temperature: -20º ~+60℃ 5. IP Level: IP54 III. Connecting Instruction 1.Power input connect to PCB board terminal, Working power 12V–265V DC/AC 2 SW1 switch It’s the switch for switching LED in flickering or lighting, When SW1 at connecting, LED will flicker after power on; When SW1 at disconnecting, LED will light after power on
    read more
  • Indoor wireless keypad in 433mhz keypad
    IMPORTANT SAFETY INSTRUCTIONS Warnings! To reduce the risk of injury, do not attempt to use this product until you have read thoroughly and understand completely this operator’s manual and the operator’s manual for the RYOBI garage door opener. Ensure compatibility and fit before using this accessory. Do not use this accessory if a part is damaged or missing. n Install keypad in sight of garage door and at least five feet above the floor. n Always keep the moving door in sight and away from people and objects until it is completely closed. No one should cross the path of the moving door, which can result in death or serious personal injury n Do not allow children or untrained individuals to use this unit. n Do not allow to be used as a toy. Close attention is necessary when used near children. n Save these instructions. Refer to them frequently and use them to instruct others who may use this product. PACKING LIST Wireless Indoor Keypad, AA Batteries (2), Screws (2), Operator’s Manual

    hot tags :

    Wireless keypad 433mhz
    read more
  • DC24V Automatic Swing Gate Operator Automatic Swing Gate Operator/garage door motor
    Standad kit components                                                             2* Arms Gate Openers 2* Transmitters 1* Control Panel 2* Gate Bracket 2* Post Bracket 1* Manual 2* Allen Key A set of Hardware Accessories Produect feacture                                                                        1.Easy to install and operate,and easy to connect wired. 2.Open and close the gate by remote control and keypad. 3.Time promotation function.when open gate,speed is slow,then a little quick,and when close the door,speed is slow again. 4.In case of power failure,release the clutch easily,and can operate the gate manually. 5.Stop working when gate meets with obstacle.  6.Rod's max travel is 300mm. 7.Motor's Poweer : 24VDC 40W 8.Running Speed :1.6cm/s                   9.Run travel : 300mm 10. Max single leaf gate width: 2M 11.Max single leaf gate weight: 100-150KG  Produect feacture                                                                        Digital LED Menu brings a easy setting ,plug and play Availble to set pedestrian mode Adjustable working time  Adjustable resistance sensitiv Adjust auto-closing time Terminal availble for loop detector ,photocell,push button, keypad , access control equipment etc. Custom rolling code makes the system more secure, high anti-theft performance
    read more
  • Gate Flash lamp top Gate Flash lamp reviews
    I. Safety Instruction 1. For security, please read the user manual carefully before initial operation; 2. Please be sure the power is off before connecting, the product is produced without fuse; 3. This system must not endanger life or property during the running failure or its security risks have II. Technical Specification 1. working voltage: 12-265VAC /DC 2. Loading capacity: <3W 3. Flicker Frequency: 1HZ 4. Working temperature: -20º ~+60℃ 5. IP Level: IP54 III. Connecting Instruction 1.Power input connect to PCB board terminal, Working power 12V–265V DC/AC 2 SW1 switch It’s the switch for switching LED in flickering or lighting, When SW1 at connecting, LED will flicker after power on; When SW1 at disconnecting, LED will light after power on
    read more
  • 2018 New Tubular Motor Receiver for Roller Shutter Door Tubular Motor Receiver
    1.General For safety, please read the manuals carefully before initial operation; making sure that the power is off before any operation. The controlling signal may be interfered by other RF communication devices in same frequency range. Prohibited using this to control any high risk industrial equipment or system (e.g.cranes). Always install it indoor or under the rain cover protection.   2.Specification Power Supply: AC220V/50HZ. Loading Capacity: 2000W, AC240V. Frequency: 433.92 MHz. Memory Capacity: 50PCS rolling code remote control. External button and photocell protection. Working Temperature:  -20℃ to 60℃.   3.Learning/Removing Remote Control Press and release the Learn button, LED indicator on, then press the button of remote control, LED indicator flashes 2 times, new remote has been learned successfully. There is no signal received from remote control within 10s, then LED indicator goes off and exit learning mode. If you have already learned 50PCS up to the maximum memory capacity, the next remote control will not be learned. The LED indicator will flash 5 times and exit learning mode. 3.1 Wireless self-learning With this function, you could add the new remote control from the old remote control without accessing to the receiver. Press 2 and.3 button of old remote control at the same time for 6 seconds, then press any button of new remote control.   3.2 Removing Remote Control  Press and hold learn button 10 seconds until the LED indicator lights on then all the learned remote controls have been removed successfully. 4. Product Overview                 : Open Button  ‚: Stop Button  ƒ: Close Button  „: Learn Button …: 0.5A Built-in fuse for board   †: 10A Built-in fuse for motor  ‡: LED Indicator ˆ: Dip Switch For Setting Different Mode
    read more
  • 433mhz/315mhz Wireless Keypad for gate opener Wireless Keypad for gate  opener
    Product overview --Power supply: DC 6V ( 4pcs AAA 1.5v dry battery). --Touch keyboard: 1-9, *, 0, #. --Standby current: 18uA (Sleep mode), 6mA ( working mode). --Working current: 28mA ( working mode). --Three LED indicator light: Red, Green, Blue. --Low battery indication: If the battery is low, keypad would have beep indication after every signal transmission is made. -- Anti-vandal alarm. When the keypad is disassembled illegally, the buzzer will “beep” to alert. -- 4 digits installer’s pin code and 4 digits user’s pin code setting. -- RF learning code function: can learn commonly used fixed code, HCS301 rolling code. -- Two channels RF 433MHZ transmitting. -- Scrambled pin code. -- Keypad buzzer on/off. -- Keypad back light on/0ff. -- Keypad security lock. -- Factory default setting -- Weatherproof Operation Instruction: -- When keypad enters programming mode, if the keypad does not receive the further command within 6s, keypad would exit programming mode automatically. -- When misoperating the keypad during programming, you can enter programming mode again after keypad exits programming mode automatically. -- When received the command “*”or “#”, keypad would receive the command then judge the command is correct or not. If it is incorrect command, keypad would exit programming mode; or it is correct command, keypad would operate further. -- When programming, if user key in users’ pin code more than 4 digits, the keypad would recognize it as incorrect operation, then exit programming mode. -- When keypad in working mode, if the interval time between inputting each digit is more than 6s, keypad would ignore the previous digit. --if keypad is not learning any code, the red LED indicator would flash 5 times
    read more
  • 2018 NEW!!! Infrared photocell beam sensor top 2018 NEW!!! Infrared photocell beam sensor reviews
    TECHNICAL DATA: 1.Power Supply: AC/DC 12-24V 2.Working Current: Transmitter: ≤30mA; Receiver: ≤50mA 3.Infrared Wavelength: 890nm 4.Operating Distance: ≥12M 5.Adjusting angle of PCB:±90° 6.Receiver Relay Contact Output: Max. 1A at 24V DC 7.Operating Temperature: -20℃~+60℃ 8.N.C. Or N.O. Can Be Set Through Jumper on Receiver Photocell 9.Protection Rating: IP54 INSTALLATION INSTRUCTION: The photocells should be installed at height of more than 20cm above the ground. And the distance between transmitter and receiver should be more than 50cm. The user should install the photocells on the back of the direct sunlight or other strong light source to keep it working steadily.   Avoid installing other infrared transmitter within effective distance of receiver.   Do not use this photocell on installations in which two or more photocells are installed in parallel and close together.   If the end users need to install other photocells in one same straight line, the receivers could be installed in the two ends and the emitters could be back-to-back installed   Stable installation could avoid the signal of emitter and receiver skewing due to lightly vibrate and the malfunction.   When the product is installed in some place with angle, end user could adjust the PCB to make the installation better.   Connecting power after checking no error of connecting lines, emitter LED lights, keep the CAP of emitter and receiver align, receiver LED off; When they are not align, receiver LED on.   Wiring Connect up following the wiring diagram as below. Set the N.O. or N.C. control through the jumper on the receiver photocell based on your application as below Always consult the wiring instructions for the control unit to which you are connecting the photocells.
    read more
  • RFID Card Reader Gate opener Hands free device card reader
    Hands free device RFID card reader gate opener,
    read more

copyright © 2018 Giant Alarm System Co.,Ltd. All Rights Reserved dyyseo.com

top

the professional team to service!