Products

  • 2018 New Tubular Motor Receiver for Roller Shutter Door Tubular Motor Receiver
    1.General For safety, please read the manuals carefully before initial operation; making sure that the power is off before any operation. The controlling signal may be interfered by other RF communication devices in same frequency range. Prohibited using this to control any high risk industrial equipment or system (e.g.cranes). Always install it indoor or under the rain cover protection.   2.Specification Power Supply: AC220V/50HZ. Loading Capacity: 2000W, AC240V. Frequency: 433.92 MHz. Memory Capacity: 50PCS rolling code remote control. External button and photocell protection. Working Temperature:  -20℃ to 60℃.   3.Learning/Removing Remote Control Press and release the Learn button, LED indicator on, then press the button of remote control, LED indicator flashes 2 times, new remote has been learned successfully. There is no signal received from remote control within 10s, then LED indicator goes off and exit learning mode. If you have already learned 50PCS up to the maximum memory capacity, the next remote control will not be learned. The LED indicator will flash 5 times and exit learning mode. 3.1 Wireless self-learning With this function, you could add the new remote control from the old remote control without accessing to the receiver. Press 2 and.3 button of old remote control at the same time for 6 seconds, then press any button of new remote control.   3.2 Removing Remote Control  Press and hold learn button 10 seconds until the LED indicator lights on then all the learned remote controls have been removed successfully. 4. Product Overview                 : Open Button  ‚: Stop Button  ƒ: Close Button  „: Learn Button …: 0.5A Built-in fuse for board   †: 10A Built-in fuse for motor  ‡: LED Indicator ˆ: Dip Switch For Setting Different Mode
    read more
  • 433mhz Wireless Keypad for gate opener Wireless Keypad for gate  opener
    Product overview --Power supply: DC 6V ( 4pcs AAA 1.5v dry battery). --Touch keyboard: 1-9, *, 0, #. --Standby current: 18uA (Sleep mode), 6mA ( working mode). --Working current: 28mA ( working mode). --Three LED indicator light: Red, Green, Blue. --Low battery indication: If the battery is low, keypad would have beep indication after every signal transmission is made. -- Anti-vandal alarm. When the keypad is disassembled illegally, the buzzer will “beep” to alert. -- 4 digits installer’s pin code and 4 digits user’s pin code setting. -- RF learning code function: can learn commonly used fixed code, HCS301 rolling code. -- Two channels RF 433MHZ transmitting. -- Scrambled pin code. -- Keypad buzzer on/off. -- Keypad back light on/0ff. -- Keypad security lock. -- Factory default setting -- Weatherproof Operation Instruction: -- When keypad enters programming mode, if the keypad does not receive the further command within 6s, keypad would exit programming mode automatically. -- When misoperating the keypad during programming, you can enter programming mode again after keypad exits programming mode automatically. -- When received the command “*”or “#”, keypad would receive the command then judge the command is correct or not. If it is incorrect command, keypad would exit programming mode; or it is correct command, keypad would operate further. -- When programming, if user key in users’ pin code more than 4 digits, the keypad would recognize it as incorrect operation, then exit programming mode. -- When keypad in working mode, if the interval time between inputting each digit is more than 6s, keypad would ignore the previous digit. --if keypad is not learning any code, the red LED indicator would flash 5 times
    read more
  • 2018 NEW!!! Infrared photocell beam sensor top 2018 NEW!!! Infrared photocell beam sensor reviews
    TECHNICAL DATA: 1.Power Supply: AC/DC 12-24V 2.Working Current: Transmitter: ≤30mA; Receiver: ≤50mA 3.Infrared Wavelength: 890nm 4.Operating Distance: ≥12M 5.Adjusting angle of PCB:±90° 6.Receiver Relay Contact Output: Max. 1A at 24V DC 7.Operating Temperature: -20℃~+60℃ 8.N.C. Or N.O. Can Be Set Through Jumper on Receiver Photocell 9.Protection Rating: IP54 INSTALLATION INSTRUCTION: The photocells should be installed at height of more than 20cm above the ground. And the distance between transmitter and receiver should be more than 50cm. The user should install the photocells on the back of the direct sunlight or other strong light source to keep it working steadily.   Avoid installing other infrared transmitter within effective distance of receiver.   Do not use this photocell on installations in which two or more photocells are installed in parallel and close together.   If the end users need to install other photocells in one same straight line, the receivers could be installed in the two ends and the emitters could be back-to-back installed   Stable installation could avoid the signal of emitter and receiver skewing due to lightly vibrate and the malfunction.   When the product is installed in some place with angle, end user could adjust the PCB to make the installation better.   Connecting power after checking no error of connecting lines, emitter LED lights, keep the CAP of emitter and receiver align, receiver LED off; When they are not align, receiver LED on.   Wiring Connect up following the wiring diagram as below. Set the N.O. or N.C. control through the jumper on the receiver photocell based on your application as below Always consult the wiring instructions for the control unit to which you are connecting the photocells.
    read more
  • RFID Card Reader Gate opener Hands free device card reader
    Hands free device RFID card reader gate opener,
    read more
  • 24V LED flashing lamp for automatic gate top 24V LED flashing lamp for automatic gate reviews
    24V LED flashing lamp for automatic gate
    read more
  • Gate Opener Flashing light Lamp Gate Opener Flashing light
    sed for  for swing gate opener ,sliding gate opener,barrier gate and other gate operators.
    read more
  • Wireless access keypad wireless keypad for gate opener
    The wireless keypad is an very intelligent gate opener at present. 12buttonS on keypad .Easy to operate and wiring connection .
    read more
  • AC 110V/220V Sliding gate control board Sliding gate control board
    Control Board Characteristics:    1. Input voltage (Supply Voltage): 220V AC/110V AC    2. Transmitter Coding: Factory Custom Rolling Code.    3. Allowed Transmitters: Up to 30PCS Transmitters.   4. Versatility: Suitable for sliding gate openers.  Function Testing The following functions refer to the diagram above.  Auto Learn NOTE: The receiver can memorize more than 15 remote controls. 1.    Press the “AUTO LEARN” button (1), LED-D5 will light for 10 seconds, by pressing the remote control button during the 10 seconds the receiver will accept the code, the LED-D5 will go off and the motor will start. 2.    If no remote control button is pressed within the 10 seconds, LED-D5 will go off and the learning function will be exited. 3.    To delete the memory code, press the remote control button continuously for 6 seconds, LED-D5 will flash to denote all memory codes have been deleted.
    read more
  • GSM RTU5025 top GSM RTU5025 reviews
    1. Product details The RTU5025 is an upgraded version of famous RTU5015 gate opener, a very simple device which can be used for remote control swing or sliding gates and doors or switching devices with authorized access management(Caller-ID),well used on door access, gate control, remote switching, or car parking systems. Actually the RTU5025 can be used in places which require to turn ON/OFF your system, machines, equipments remotely with a FREE phone call from your mobile or fixed line telephone. Android APP on Google Play available, PC software for programming via USB, remote server system over TCP/IP supported*,users can easily download the access historical data anywhere anytime. 1.1 Advantages Ø  GSM or 3G band, distribute worldwide applications; Ø  Up to 999 authorized phone numbers can be configured at the specified time for access control; Ø  No call charges. Reject calls from authorized number then carries out the turn ON/OFF action on the first 'ring'; Ø  Secure – Using Caller-ID for verification, unknown phone calls are ignored; Ø  SMS confirmation of relay actions(door open) to the owner or authorized caller number. Ø  No need remote control or keys for different users; Ø  Up to 1,000 events log, download the operation historical data by USB or over GPRS; Ø  Ø                   Android APP for configuration. Digital Inputs Ø  One Digital input for motion sensor or other sensors to protect your door and windows, SMS alert to owner immediately when triggered; Ø  One Digital input special for secure door and automatically armed when door closed, SMS alert to owner immediately when door opened illegally. Setting Ø  Android APP, SMS command or PC Software programming; Ø  Operate from anywhere anytime, no distance limitation;

    hot tags :

    GSM RTU5025
    read more

copyright © 2020 Giant Alarm System Co.,Ltd. All Rights Reserved dyyseo.com

top

the professional team to service!